mso-hansi-font-family:"Times New Roman"">一、橡膠壓縮永久變形器概述：

mso-hansi-font-family:"Times New Roman"">永久壓縮變形器由平行鋼板、插銷、限制器和緊固件組成, mso-hansi-font-family:"Times New Roman"">符合GB7759-2015 "Times New Roman"">、ISO815-1:2008 "Times New Roman"">要求,用于硫化橡膠, mso-hansi-font-family:"Times New Roman"">熱塑性橡膠在常溫, "Times New Roman"">高溫和低溫條件下, "Times New Roman"">以一定壓縮率, "Times New Roman"">經一定的壓縮時間后測定橡膠變形。

mso-hansi-font-family:"Times New Roman"">二、橡膠壓縮永久變形器技術參數：

1、試樣 A mso-hansi-font-family:"Times New Roman"">型：真徑29mm, "Times New Roman"">高12.5mm "Times New Roman"">；B型：真徑13mm, mso-hansi-font-family:"Times New Roman"">高6.5mm

2、限制器高度? "Times New Roman"">試樣類型????????? ??A??????????????????? B

??????????? mso-hansi-font-family:"Times New Roman"">壓縮率為25% "Times New Roman"">時mm????? 9.3-9.4?????????? 4.7-4.8

??????????? mso-hansi-font-family:"Times New Roman"">壓縮率為15% "Times New Roman"">時mm????? 10.6-10.7?????? ??5.3-5.4

??????????? mso-hansi-font-family:"Times New Roman"">壓縮率為10% "Times New Roman"">時mm????? 11.25-11.3??????? 5.65-5.7

???? "Times New Roman"">硬度小于80IRHD "Times New Roman"">壓縮率為【25 "Times New Roman"">±2%】限制器

???? 80IRHD mso-hansi-font-family:"Times New Roman"">至89IRHD "Times New Roman"">壓縮率為【15 "Times New Roman"">±2%】限制器

???? 90IRHD "Times New Roman"">至95IRHD "Times New Roman"">壓縮率為【10 "Times New Roman"">±2%】限制器

3、外形尺寸：直徑110mm? "Times New Roman"">單板厚度15mm

4、重量： 10Kg

mso-hansi-font-family:"Times New Roman"">三、橡膠壓縮永久變形器使用方法：

1、在壓縮夾具的壓縮板表面上涂一層潤滑劑( mso-hansi-font-family:"Times New Roman"">滑石粉、甲基硅油) "Times New Roman"">。使試樣不粘夾具。所用的潤滑劑對試驗中的橡膠無影響。并且在試驗報告中注明所用的潤滑劑。

2、調整厚度計指針為零, mso-hansi-font-family:"Times New Roman"">測量試樣中心部份的高度(h0) "Times New Roman"">。三個試樣高度相差不超過0.01mm "Times New Roman"">。

3、將試樣、限制器置于夾具中, mso-hansi-font-family:"Times New Roman"">均勻地壓縮到規定的高度(h0), "Times New Roman"">壓縮時試樣、限制器不能互相接觸。

4、把已裝有試樣的壓縮夾具或試驗容器放入達到的試驗溫度即開始計算時間。

5、常溫或高溫試驗結束后, mso-hansi-font-family:"Times New Roman"">立即松開緊固件, "Times New Roman"">把試樣放置于木板上, "Times New Roman"">在標準溫度環境下, "Times New Roman"">自由狀態下放置(30 "Times New Roman"">±3)min, "Times New Roman"">然后用厚度計測量試樣恢復高度h1), "Times New Roman"">精確到0.01mm "Times New Roman"">。也可以讓整個壓縮夾具在室溫下冷卻30~120min, "Times New Roman"">再從壓縮夾具中取出試樣; "Times New Roman"">停放30min "Times New Roman"">測一試樣高度。但應在報告中注明停放時間。

6、低溫試驗報告后, mso-hansi-font-family:"Times New Roman"">在低溫箱中立即松開緊固件同時開始測量試樣高度(h2), mso-hansi-font-family:"Times New Roman"">如條件允許下最好每隔一段時間測量試樣的高度, mso-hansi-font-family:"Times New Roman"">時間分別為1Os "Times New Roman"">、30s、1min mso-hansi-font-family:"Times New Roman"">、3min "Times New Roman"">、10min、30min mso-hansi-font-family:"Times New Roman"">和2h "Times New Roman"">。這樣可繪出試樣高度與時間的對數曲線圖。取試樣應使用鑷子鉗。

7、耐液體試驗時, mso-hansi-font-family:"Times New Roman"">先在試驗容器內放入液體, "Times New Roman"">液面為容器高度的二分之一, "Times New Roman"">然后把裝有試樣的壓縮具放入容器內。試樣必須浸沒在液體中。試驗用的液體不能重復使用。不同配方的試樣不可在同一試驗容器中進行試驗。在液體中試驗結束后, mso-hansi-font-family:"Times New Roman"">將試驗容器冷卻至接近室溫, "Times New Roman"">再把壓縮夾具從容器中取出, "Times New Roman"">夾具可用汽油等洗滌, "Times New Roman"">時間不超過30s "Times New Roman"">，然后按本標準7.5.1 "Times New Roman"">進行測量,并在報告中注明試驗容器的冷卻時間。

8、整個試驗結束后，檢查試樣內部有否缺陷、氣泡，反之，試樣作廢。

?

?